How to Lock Vinyl Plank & Laminate Under Door Jambs (Shaving the Locking Lip & Best Glue Guide)
Once a plank slides underneath an undercut door jamb, the door frame blocks you from lifting the plank at an angle to click it into the locking groove. To make the plank slide in completely flat, carefully shave off the tiny upward locking lip on the bottom groove using a utility knife or sharp wood chisel. Then replace that mechanical lock with adhesive: for Vinyl Plank (LVP), lightly moisten the groove with a damp sponge and apply a thin bead of non-foaming Clear Gorilla Glue (keep denatured alcohol handy for cleanup). For Laminate Flooring, use standard PVA Wood Glue (like Titebond III). Tap the plank flat and tight, then hold the joint overnight with blue painter's tape.
One of the most stressful moments in any DIY flooring project happens right at a hallway doorway. You undercut the door jamb cleanly, slide your plank underneath the casing, and suddenly realize you are trapped: the door jamb won't let you tilt the plank up at an angle to lock the click-joint together.
If you try to force or pound an unmodified plank together completely flat, you will either crush the delicate locking tongue or leave an ugly, raised cross-joint that pops apart a week later. Fortunately, there is a simple trade modification I use on almost every hallway install that lets you slide stubborn doorway planks together completely flat—and lock them permanently in place.
In this step-by-step video, I show you how to plan your hallway doorway joints with The Layout Buddy, mark door frames with a Cheater Board, shave the locking lip, and glue the joint flat with Clear Gorilla Glue.
Step 1: Make the Long Joint Land Inside the Doorway First
Before you touch a chisel or a utility knife, remember my Priority #1 Layout Rule from my Multi-Room Flooring Layout Guide: whenever your planks run parallel to a doorway (like down a hallway with bedrooms branching off), always plan your starting row width so the long joint of the plank lands right inside the doorway.
Why does that matter so much? When the long seam lands inside the doorway opening instead of wrapping a single plank around both sides of the door frame like a "C", you don't have to wrestle a notch around both sides of the jamb at once. I lock 10 planks together and stretch The Layout Buddy across them to mark my exact plank widths for 25 feet—allowing me to trim a few inches off my very first starting row so the long joints land cleanly inside my hallway doorways.
Step 2: Mark the Doorway Using a "Cheater Board"
When you reach the doorway row, stack the plank you are about to cut directly on top of the last installed row, lining up the locking systems edge-for-edge. To transfer the exact contour of the wall and undercut door jamb onto your plank, make what I call a Cheater Board:
- How to Make a Cheater Board: Take a scrap piece of plank and trim back a small portion of the bottom groove lip. The more of that bottom groove lip you trim off, the smaller your expansion gap will be; the more you leave on, the wider your gap.
- Slide & Mark: Hold your Cheater Board tightly against the wall (giving you an automatic 1/4" expansion space), and slide it underneath the undercut door jamb at a slight angle so your plank will clear the frame easily when sliding into place. Trace along your Cheater Board with a pencil and make your doorway cuts with a general-purpose jigsaw blade.
Step 3: How to Shave the Locking Lip So the Plank Slides In Flat
Look closely at the bottom groove edge of your vinyl plank or laminate board. You will see a tiny upward ridge—the locking lip—at the outer tip of the lower groove. That little upward bump is what forces you to tilt a plank at a 30-degree angle to snap it together.
When a plank is already slid underneath a door jamb, you cannot lift it at an angle. To let the tongue slide straight in horizontally while both planks lie flat on the subfloor, you simply remove that upward lip along the section entering the doorway:
- Use a Sharp Utility Knife or 1" Wood Chisel: Run a sharp utility knife blade slowly along the base of the upward locking lip (using the lip itself as a guide over 2 to 3 light passes), or plane the bump flat with a sharp Spec Ops 1" Wood Chisel. (If you have a long hallway wall to modify, you can even skim that tiny lip off on a table saw.)
- Do NOT Cut Off the Entire Bottom Groove Ledge: Only shave the tiny upward bump off the top of the bottom groove ledge. Leave the flat bottom shelf intact so the two planks still rest on one another and stay flush in height!
- Test With a Scrap Piece First: Before gluing a full row, test-slide a small modified scrap piece into the installed plank flat on the floor to make sure the joint closes tight without binding.
Step 4: Which Glue Should You Use? (Vinyl Plank vs. Laminate)
Once you shave that mechanical locking ridge off, nothing is stopping the two planks from pulling apart laterally over time unless you glue the joint. Never use the wrong glue for your flooring material—here is the exact breakdown I use in the field:
Non-Foaming Clear Gorilla Glue
Standard wood glue won't bond securely to non-porous PVC or stone-polymer vinyl cores, and original brown Gorilla Glue foams up and oozes an ugly brown crust onto your planks. Always use Clear Gorilla Glue—it is non-foaming and bonds vinyl locking joints rock-solid.
- Crucial Water Trick: Wipe the locking groove with a damp water sponge before applying a small bead of glue—water activates Clear Gorilla Glue!
- Easy Cleanup: Keep denatured alcohol and a rag right beside you to wipe any squeeze-out off the plank face or your hands before it cures.
Titebond III PVA Wood Glue
Traditional laminate flooring has a high-density wood fiber (HDF) core. When you shave the locking ridge on laminate, standard PVA Wood Glue (like Titebond III) soaks directly into the wood fibers and creates a bond stronger than the core itself.
- No Water Sponge Needed: Apply a thin, continuous bead directly onto the bottom shelf of the modified groove.
- Easy Cleanup: Wipe away any squeeze-out immediately using a damp water cloth—no solvents required.
Interactive Door Jamb Locking & Glue Advisor
Select your flooring material and doorway setup below to see the exact lip modification, glue activation rule, and cleanup checklist for your doorway:
• Locking Lip Modification: Cut reliefs into the drywall/paneling beside the jamb so you can slide the plank deeper first, then shave the upward locking lip along the full groove so it slides back flat into the joint.
• Adhesive & Activation: Dampen the locking groove with a wet sponge first (water activates the adhesive), then apply a thin bead of Non-Foaming Clear Gorilla Glue.
• Tapping & Overnight Hold: Tap the joint flat and tight with The Plank Hammer, wipe any squeeze-out immediately with denatured alcohol, and strap 21 strips of blue painter's tape (3 per doorway) across the seam overnight.
Step 5: Tap It Tight Flat & Tape It Overnight
Once your locking lip is shaved and your glue is in the groove, you don't even have to fight the plank in mid-air. Here is my preferred way to close the joint cleanly:
- Set the Plank Flat in Place: Slide the plank underneath the door jamb first and set it down flat against the neighboring row. You can even slip the tip of your utility knife under the joint edge while moistening the groove with a damp sponge and squeezing in your thin bead of Clear Gorilla Glue.
- Tap Straight In With The Plank Hammer or Plank Puller: Drop the plank flat and tap it straight into the glued groove using The Plank Hammer (keeping the face flat against the plank edge so you never mar the bevel) or pull the end tight from the wall side with The Plank Puller.
- Wipe Squeeze-Out Immediately: As the seam closes tight, a tiny bit of glue may squeeze up. If you are installing vinyl plank with Clear Gorilla Glue, wipe the seam and your fingers right away with a rag dampened with denatured alcohol.
- Strap Blue Painter's Tape Across the Joint Overnight: Stretch strips of blue painter's tape tightly across the glued seam every 12 to 16 inches and leave the tape on overnight so the planks cannot creep apart while the glue cures.
Quick Reference: Door Jamb Glue & Tool Cheat Sheet
| Task / Step | Vinyl Plank (LVP / SPC / WPC) | Laminate Flooring (HDF Wood Core) |
|---|---|---|
| 1. Hitting Doorways Cleanly | Plan row widths with The Layout Buddy so long joints land in doorways | Plan row widths with The Layout Buddy so long joints land in doorways |
| 2. Shaving the Locking Lip | Utility knife (2–3 slow passes), 1" Wood Chisel, or table saw | Sharp 1" Wood Chisel or table saw |
| 3. Required Adhesive | Non-Foaming Clear Gorilla Glue (Never brown foaming glue!) | Titebond III PVA Wood Glue |
| 4. Pre-Glue Moisture Step | Yes — wipe groove with a damp water sponge to activate glue | No — apply directly to dry wood-fiber groove |
| 5. Squeeze-Out Cleanup | Denatured alcohol on a clean rag + blue tape overnight | Damp water rag immediately + blue tape overnight |
By the way, if you like the wide 9" x 72" rigid-core vinyl plank I'm installing in the doorway video above, that is Flooret Modin Signature—use my coupon code SOTHATSHOW50 to get 50% off samples with free shipping. And before you start your hallway, make sure you check out my 8 Clever Plank Flooring Tips to Avoid Beginner Blunders.
Get My Custom Pro Flooring Tools & Step-by-Step Coaching
Stop fighting stubborn locking joints under door jambs and tight walls. Grab The Layout Buddy to make your long joints land right in your doorways, and use The Plank Hammer and The Plank Puller to tap shaved doorway joints closed without damaging a single plank edge.